Friday, January 14, 2011

Near Space in a Can



The Near Space in a Can thermal vacuum chamber is about ready for retail. The image above is missing its vacuum gauge, which is at school. Otherwise, you now get a good idea of what it will look like. The kit should be no more than $150.


Just pack the Near Space in a Can with dry ice and let it chill before loading the test subject inside. Then pump it down with your vacuum pump. The environment inside will match near space conditions.


The stainless steel canister is 7.5 inches in diameter and 7.5 inches deep. The clear plexiglass cover lets you observe the experiment inside and even video tape the test.


A future upgrade will bring wiring inside so you can communicate with experiments inside.

Sunday, January 9, 2011

Single Axis Arm with Snare End-Effector



I completed my design of a single axis robotic arm. The servo lifts and lowers the arm like a traditional arm. What is different is the end effector that allows the arm to pick up objects. It's a wire snare, similar to the end effector on the Space Shutter robotic arm. A mini servo extends and retracts the wire snare, letting it wrap around and tighten around th object to be picked up.

Look for a magazine article (in Servo) and a kit to made available shorty.

Saturday, January 1, 2011

Near Space in a Can

I ran the first tests of a new thermal vacuum chamber. It's a stainless steel can with vacuum and cable ports. The can fits inside a plastic ice chest that can be packed with dry ice (see my Nuts and volts article on this subject).

The front of the chamber is sealed with thick acrylic plastic to permit observations of the interior of the chamber during testing. The cable port permits power to enter the chamber for its ultraviolet source and temperature sensor. Pressure inside the chamber is monitored with an analog pressure gauge.

I call the thermal vacuum chamber, Near Space in a Can. It's the second simulator NearSys will sell (the GPS simulator is the first). Near Space in a Can is large enough to test BalloonSats and CubSats.

Near Space in a Can will be available from NearSys in 2011 as an affordable kit.

Robot Terminal

I finally had time to figure out how to send AT commands to the Digi Xbee radios. I've worked with them previously, but wasn't comfortable enough with how I was setting the radios. Now I've got them working the way I want.

Therefore, I will shortly be offering a robot terminal kit. It will permit you to communicate with a robot using your PC. I've got an example robot set up right now. It drives and turns as instructed while confirming the communications. The robot carries a simple arm and video transmitters that is also controlled over the radio. The robot is smart, it attempts to carry out your commands as best it can. Since the robot is using a ChapBot-14, it is a little limited - so eventually, I'll interface the radio with a CheapBot-18 on an articulated robot body and more complex arm. Moon rover anyone?

I'll also create a kit to allow BalloonSats to communicate with each other in order to create near space constellations.

Wednesday, December 29, 2010

GPS Simulator

Work has started on a GPS simulator that will eventually become a NearSys kit. The simulator creates the GPS sentences that a near spacecraft will see on a typical mission. The ascent rate and burst altitude are all programmable. It's also possible to create a lose of satellite lock.


The GPS simulator will allow anyone with a programmable flight computer to test their flight code on the ground. It will also let anyone with an APRS tracker observe the behavior of their tracker without leaving the ground.


The simulation will reduce the risk of mission failure due to unforeseen behavior caused by high altitude GPS sentences. It also will let inidividuals run a test on their entire near spacecraft to observe that it will function as desired. Tests like this increase the number of successful near space missions.




Next up is the near space simulator, a totable thermal vacuum chamber called Near Space in a Can.

Wednesday, December 15, 2010

NearSpace Easy Flight Computer

I've started testing on a new near space flight computer, the NearSpace Easy. It operates with a BASIC Stamp 2pe and shares the GPS data stream in parallel with a Tiny Trak 3. The Easy digitizes up to eight channels of analog data with a resolution of 12 bits. In addition, there are six digital ports and three servo ports.

A male DB-9 on the PCB is the GPS port. It provides power over pin 4 to the GPS as soon as it's plugged in. The GPS receivers NearSys will start selling are designed to interface to this flight computer (and the NearSpace UltraLight).

Connected by a wrapped cable is the flight computer's control panel. The panel mounts to the airframe of the near spacecraft to allow you to program both the flight computer and the APRS tracker, without having to open up the airframe. Also on the control panel are three power switches for the flight computer, servos, and audio beacon. Four indicator LEDs signal when the flight computer and servos have power, when the Tiny Trak has a GPS lock, and when the Tiny Trak is transmitting a position report. Finally, there is a mission commit pin that prevents the flight computer from recording data on the ground.

The NearSpace Easy can record up to 30 kb of data. In addition, USB jump drive adapters are sold for the BASIC Stamp that allow the storage of even greater amounts of data.

Not shown is the antenna. An antenna kit is part of the NearSpace Easy. It's a 2m dipole on the end of an RG-174 coax.

The NearSpace Easy is literally a plug and play near space flight computer. You'll need to select you battery (use a rechargeable lithium) and battery plug, but otherwise, just plug in the antenna and GPS and you're ready for a near space mission.


Wednesday, December 8, 2010

GPS Recievers - Real and Simulated

NearSys is preparing to sell GPS reciever kits for use with its near space flight computers and BalloonSat Extreme. The GPS receiver is the UniTraQ GT-320 with high altitude firmware.




The kit will include mounting materials, project box, and DB-9 connector. The GPS is designed to draw power through its DB-9 connector, so plug it into a flight computer and it's ready to produce output, no extra batteries required.


NearSys is also testing a new version of its GPS simulator. This version 2.0 will become a kit and produces more GPS sentences than before. It's greater sentence output make it a better near space and rocket flight mimic. You'll download the program with your desired flight parameters set and plug it into the flight computer. It's two buttons allow you to control when the GPS has a lock (or loses a lock) and when the balloon launch begins. The LEDs indicate power, status of GPS lock, and ascent/descent. Mission elapsed time (MET) and altitude are optionally displayed on a PC or laptop running the PICAXE program editor.